HyperLynx is a signal integrity analysis tool in PCB systems design, developed by Mentor Graphics.
Serpentine line self-crosstalk simulation in Hype......
?/ÞÆ?«¶Â0j{m¢Ç?¶?gzV²jwl? Ú?«??+r?jZr×o+®?§¶)Þ?)Þ¥«mz¹ìr§çÿëb¶Ç??Éèr§ë¢éÝ?qò¥êåÊ|l?k¥j......
asked by aleilee2008 lastest answer by Charles.Grasso
0
votesReg :Altera Encrypted Hspice simulation
Dear all,We are using Altera Fpgs in our design.We are doing Signal integrity forthe design.Altera p......
asked by gkravi.1988 lastest answer by Arpad_Muranyi
0
votes1
answersIBIS-AMI HSS15 model?
Experts,Iâ??ve gotten this question from a potential HyperLynx customer and waswondering if anyone c......
asked by cuong lastest answer by yu.yanfeng
0
votes1
answersHyperlynx far end crosstalk simulation issue
Sorry for the messy code. Have no idea what happened. Resent this email...Hi experts,It's known that......
asked by lmt8885 lastest answer by jeff.loyer
0
votes7
answersHyperlynx Far-end crosstalk simulation issue
'±¥êí³ò-þÉ'£ í?«\¢jZçp?Øf?Êè²Úâ§ö§i×^u·§yø¡û-®*e?w«¢ëb?¬Íêè}ªÿzw\®?,µ©düQOöÞq«¬z?Úºx?¢¹?®Ë«®?......
asked by lmt8885
0
votes0
answersJob Description for Project Signal Integrity Engr......
Bob Savatovic here again . . . earlier today I had posted the Project Signal Integrity Engr positi......
asked by dmarc-noreply
0
votes0
answersHyperlynx - Assigning Pins from ibis
I need some help with a particular IBIS model.When I try to assign a Pin, I get the following messag......
0
votes2
answersSenior SI Engineer Oppertunity
Hello all,Newisys(Sanmina) has an opening for a Senior SI engineer. Please contactMichael if intere......
asked by abbz100
0
votes0
answersoscillations occurring in the middle of waveform
Hello All,While simulating SI in HyperLynx I observed following waveform in oscilloscope:[cid:image0......
asked by Nachiket.Wawoo lastest answer by Nachiket.Wawoo
0
votes4
answerserror messages in IBIS Model
Hello All,I am using TC1793 Infineon Microcontroller IBIS model for SI simulation.After integrating ......
asked by Nachiket.Wawoo lastest answer by lgreen22
0
votes5
answersIBIS-AMI simulation questions
I am new at this, have used Hspice in the past, currently using Hyperlynx.Why does my eye look the s......
asked by joel lastest answer by Patrick_Carrier
0
votes1
answersgood tutorial for Hyperlynx SI
Hello Everyone,In my company I have received new task of SI using Hyperlynx tool.But I am totally ne......
asked by Nachiket.Wawoo lastest answer by rod
0
votes4
answerssparameter to TDR
Hi ,Can any one please suggest how do I convert my sparameter data to TDRI have a sparameter file ge......
asked by roopesh.badala lastest answer by Gert.Havermann
0
votes5
answersDDR4 Simulation in Hyperlynx
Hi All,Could some one clarify me on DDR4 simulation in Hyperlynx 8.2.1 :How the Data Mask for DDR4 ......
asked by shankar.electronics lastest answer by Arpad_Muranyi
0
votes1
answersDoubt about RC constant Low Pass Filter
Hi, Si-List friends,This is my first post. I do a very simple simulation in Hyperlynx about RClow pa......
asked by cnmuggle lastest answer by istvan.novak
0
votes3
answersIs it because of convergence of the simulation to......
Hi, I am using HyperLynx SI 8.2.1. When I simulate a particulartopology, I get a good result.......
asked by kbmanick lastest answer by Gert.Havermann
0
votes1
answersWG: Transmitter Jitter Setup for simulations of 5......
ResentVon: Havermann, GertGesendet: Dienstag, 25. Juni 2013 12:50An: 'Hirshtal Itzhak'; si-list@xxxx......
asked by Gert.Havermann lastest answer by Gert.Havermann
0
votes3
answersTransmitter Jitter Setup for simulations of 5Gbps
Hi Itzhak,Let me note that the proper IBIS AMI model should include jitter definitions in its ami pa......
asked by vladimir_dmitriev-zdorov
0
votes0
answersDDR3 routing Topology selection
HiWe are designing a custom board where 2 DDR3 chips (533MHz) are interfacedwith processor. There ar......
asked by sonu.goyal lastest answer by hanymhfahmy
0
votes10
answersTransmitter Jitter Setup for simulations of 5Gbps......
Hello all,I have a question relating to the proper use of jitter in hi-speed simulations of several ......
asked by ihirshtal lastest answer by Gert.Havermann
13
answers