SMA (SubMiniature version A) connectors are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw type coupling mechanism. The con
Is soldermask considered an insulator for high vo......
I am designing a power supply circuit that can have voltages up to 100 VDC.According to IPC-2221 I n......
0
votesRe: si-list Digest V16 #24
A few things to recognize, folksFirst, ANYONE can build an averaged model which is state space plane......
0
votes3
answersThere are not 2, there are six ... How to specify......
Jeff,If your design is limited to simple through hole vias, then two hole sizes are required - finis......
asked by wkatz
0
votes0
answersCreating S parameter model for simulation
Hello Experts,I would like to study the impact of different routing on mounted inductance for decoup......
asked by benoit.goral lastest answer by istvan.novak
0
votes1
answersWiring Harnessing SI Question
HI all --Hoping that list can shed some light on some wire harness related SIquestions at some very,......
0
votes4
answersLooking for appropriate forum/mailing list for ES......
Dear Experts,I have been a long time follower of the mailing list and I have thoroughlyenjoyed readi......
asked by alfred1520list
0
votes0
answersRe: Thermal measurements on a test board *** than......
Thanks allI believe my resistance measurements and temperature measurements are pretty close. And th......
asked by dbrooks9 lastest answer by dmarc-noreply
0
votes2
answersPrinting Powerpoint Slides
I sent out this message a while back and got some good advice.Unfortunately, I misplaced it and need......
asked by leeritchey lastest answer by cuong
0
votes2
answersWhat does an unpowered FPGA output look like on a......
Hello SI-list!Trying to figure out if an unpowered, area array FPGA output is connected to PCB using......
0
votes3
answersSMA launch optimization
Hi Experts,When I do SMA launch optimization, my SMA has characteristic impedance50ohm, but the trac......
asked by zhangjun5960 lastest answer by scott
0
votes2
answersModeling interconnects over silicon
Hi All,While I enjoyed reading the hilarious comments in the commodity thread,here is a technical pr......
asked by phillypham
0
votes0
answerscommodity
Hi,Did signal integrity engineering become a commodity?Or is this trend about to slap someone in the......
asked by buenoshun lastest answer by chris.cheng
0
votes26
answersde-embedded [S] measurements and IEEE
So how many times have you gotten a measured Touchstone file from a vendor and felt the data was bad......
asked by jim.nadolny
0
votes0
answersrepeat of EMC lab test error presentation for tho......
Hi All,There was a mix up on which month the presentation was, should have been Mayand I said June. ......
asked by doug
0
votes0
answerssome questions abou a PCB test coupon to measure ......
Hi experts,I have designed a PCB test coupon to measure the impedance curve andcrosstalk curve from ......
asked by zhangjun5960 lastest answer by istvan.novak
0
votes3
answersSPI 2015 in Berlin - Early Registration ends on F......
Dear colleagues,This is just a reminder that the 19th IEEE Workshop on Signal and Power Integrity (S......
asked by Ivan.Ndip
0
votes0
answerstips of using TDR probe
Hi,We're evaluating the performance of our TDR probe to determine if it can be used in VNA measureme......
asked by sherman.chen lastest answer by han.guobing
0
votes16
answersRe: PCIe Gen3 DMSI calibration concept ... RX tes......
Hi, Boris. My opinion is: 1) It makes sense to test at that calibrated state, that is really the ca......
asked by Joseph.Schachner
0
votes0
answersCapacitance of Transmission Line
Hi Experts,Happy new year!When I extract the RLCG of ideal transmission line, I observe that the cap......
asked by dmarc-noreply lastest answer by dmarc-noreply
0
votes8
answersEMC troubleshooting best done without EMC equipme......
Hi All,Now there is a provocative subject line, but to a large extent true in myexperience.Many eng......
asked by doug
1
answers